We bring to your attention a typical example of a job description for an equipment adjuster in production building materials, sample 2019. A person with primary or secondary vocational education, special training and work experience can be appointed to this position. Do not forget, each instruction of the equipment adjuster in the production of building materials is issued on hand against receipt.

It provides typical information about the knowledge that an equipment adjuster in the production of building materials should have. About duties, rights and responsibilities.

This material is included in the huge library of our site, which is updated daily.

1. General Provisions

1. An equipment adjuster in the production of building materials belongs to the category of workers.

2. A person with an average professional education or initial vocational education and special training and ____ years of work experience.

3. An equipment adjuster in the production of building materials is hired and dismissed by the director of the organization upon the presentation of _______.

4. The adjuster of equipment in the production of building materials must know:

a) special (professional) knowledge of the position:

- arrangement of pipe-cutting and pipe-turning machines for processing asbestos-cement pipes and couplings, rules for their adjustment;

- the device of hydraulic presses and the rules for their adjustment to different modes of pressing;

— standards ( specifications) for manufactured products;

- allowable tool wear dimensions;

— device and methods of adjustment of serviced equipment;

- rules for disassembly and assembly of all nodes of serviced mechanisms;

— lubrication system for serviced equipment; the device of the used working and measuring tool;

- rules of technical operation, electrical circuit of the serviced equipment and instrumentation;

- the service life of individual parts and the procedure for their replacement;

b) general knowledge of the employee of the organization:

— rules and norms of labor protection, safety measures, industrial sanitation and fire protection,

- rules for the use of funds personal protection;

- requirements for the quality of work (services) performed, for rational organization work in the workplace;

- types of marriage and ways to prevent and eliminate it;

- production signaling.

5. In its activities, the equipment adjuster in the production of building materials is guided by:

- the legislation of the Russian Federation,

— Charter of the organization,

- orders and directives organization director,

- this job description,

- The internal labor regulations of the organization.

6. The equipment adjuster in the production of building materials reports directly to ___________ a worker with a higher qualification, the head of production (section, workshop) and the director of the organization

7. During the absence of the equipment adjuster in the production of building materials (business trip, vacation, illness, etc.), his duties are performed by a person appointed by the director of the organization on the proposal of ________ in the prescribed manner, who acquires the relevant rights, duties and is responsible for the execution of the duties assigned to him responsibilities.

2. Responsibilities of the equipment adjuster in the production of building materials

Job responsibilities of the equipment adjuster in the production of building materials are:

a) Special (professional) duties:

— Adjustment of semi-automatic pipe-cutting, coupling-cutting and pipe-turning machines.

— Change of the cutting tool and installation of rollers on pipe cutting machines.

– Adjustment of hydraulic presses with a capacity of up to 5000 tons for different pressing modes in relation to the requirements of pressed products and the technology of their production.

– Adjustment, regulation and ensuring the uninterrupted operation of technological, power and transport equipment of quarries, drying, firing, clay and cement-sand tiles, expanded clay gravel, aggloporite, lime and gypsum and mass-preparation departments of sand-lime brick factories.

— Change of worn parts and units of mechanisms.

— Manufacture and replacement of small spare parts.

- Elimination of malfunctions in the operation of mechanisms.

— Lubrication of rubbing parts of mechanisms.

- Participation in the repair and acceptance of serviced equipment after repair.

- Keeping a log of equipment operation.

— Adjustment and maintenance of uninterrupted operation of unloading machines, transporting devices, crushing and screening, grinding and concrete mixing units, dosing devices and apparatus, procurement and fittings equipment.

— Observation and control of the operation of mechanisms, adjustment and regulation of the mode of their operation.

- Preliminary preparation and replacement of worn parts and assemblies.

— Instruction of service personnel in the care and operation of the equipment.

– Adjustment and ensuring the smooth operation of pumps, circular saws, drilling machines and other similar equipment.

– Installation, tension and fastening of saws in the frame of stone sawing machines.

b) General duties of an employee of the organization:

— Compliance with the Internal Labor Regulations and other local regulations of the organization, internal rules and norms of labor protection, safety, industrial sanitation and fire protection.

– Fulfillment, within the framework of the employment contract, of the orders of the employees to whom it was repaired in accordance with this instruction.

– Performing work on the acceptance and delivery of shifts, cleaning and washing, disinfection of serviced equipment and communications, cleaning the workplace, fixtures, tools, as well as keeping them in good condition.

- Maintaining established technical documentation.

3. Rights of the equipment adjuster in the production of building materials

The equipment adjuster in the production of building materials has the right to:

1. Submit proposals for management consideration:

– to improve the work related to the provisions of this responsibilities,

— on bringing to material and disciplinary responsibility employees who violated production and labor discipline.

2. Request from structural divisions and employees of the organization the information necessary for him to perform his duties.

3. Get acquainted with the documents that define his rights and obligations in his position, the criteria for assessing the quality of performance of official duties.

4. Get acquainted with the draft decisions of the organization's management regarding its activities.

5. Require the management of the organization to provide assistance, including the provision of organizational and technical conditions and the execution of established documents necessary for the performance of official duties.

6. Other rights established by the current labor law.

4. Responsibility of the equipment adjuster in the production of building materials

The equipment adjuster in the production of building materials is responsible in the following cases:

1. For improper performance or non-performance of their official duties provided for by this job description - within the limits established by labor legislation Russian Federation.

2. For offenses committed in the course of their activities - within the limits established by the current administrative, criminal and civil legislation of the Russian Federation.

3. For causing material damage organizations - within the limits established by the current labor and civil legislation of the Russian Federation.

Job description for an equipment adjuster in the production of building materials - a sample of 2019. Job Responsibilities the equipment adjuster in the production of building materials, the rights of the equipment adjuster in the production of building materials, the responsibility of the equipment adjuster in the production of building materials.

I APPROVE ________________________________ _____________________________ (name of employer) __ ________________________________ (name of position (name, address, PSRN, TIN / KPP of the head of the employer) of the employer) _______________________ (signature) (full name) "___" ________ ____ M.P.

Job (production) instruction for an equipment adjuster in paper production of the 2nd (4, 5) category _______________________________________________ (name of the employer's department)

1. GENERAL PROVISIONS

1.1. An equipment adjuster in paper production of the 2nd (4, 5) category (hereinafter referred to as the "Employee") refers to workers.

1.2. real job description defines functional responsibilities, rights, duties, responsibilities, working conditions, relationships (connections by position) of the Employee, criteria for evaluating his business qualities and results of work when performing work in the specialty and directly at the workplace in "______________" (hereinafter referred to as the "Employer").

1.3. The employee is appointed to the position and dismissed from the position by the order of the Employer in accordance with the procedure established by the current labor legislation.

1.4. The employee reports directly to _________________________.

1.5. The employee must know:

rules and regulations on labor protection, industrial sanitation and fire safety;

rules for the use of personal protective equipment;

requirements for the quality of work (services) performed;

types of marriage and ways to prevent and eliminate it;

production signaling;

requirements for the rational organization of labor in the workplace;

2nd rank:

the principle of operation of the serviced equipment, the range of units and parts that are subject to the greatest wear;

rules for the use of devices and tools;

speed setting tables; lubrication systems and grades of oils;

4th rank:

arrangement of serviced equipment, adjustment and fitter-repair work;

quality and types of materials used;

qualitative indicators finished products according to state standards.

5th rank:

design, principle of operation of the serviced equipment;

the nomenclature of units and parts subject to the greatest wear;

speed setting tables;

quality and grades of materials and semi-finished products used;

technology and quality indicators of finished products.

1.6. Qualification requirements. _______________________ education required.

2. JOB RESPONSIBILITIES

Work on the acceptance and delivery of the shift, cleaning the workplace, fixtures, tools, as well as keeping them in good condition, maintaining the established technical documentation.

2nd rank:

adjustment of equipment under the guidance of a highly qualified adjuster. Equipment adjustment and preventive maintenance. Disassembly, cleaning, lubrication and replacement of individual fixtures and tools. Systematic testing of machine tools.

4th rank:

Adjustment and adjustment of cutting, grinding and cartoning equipment. Troubleshooting equipment. Adjustment of an automatic packaging line, including a press, wrapping, turning, strapping, marking, weighing machines. Monitoring the quality of manufactured products and established technological regime equipment operation. Carrying out calculations for the optimal cutting of paper rolls. Adjustment and adjustment of bobbin wrappers, cone wrappers and semi-automatic machines under the guidance of a highly qualified adjuster.

5th rank:

adjustment and adjustment of bobbin, cone wrapping machines and semi-automatic machines. Self-adjustment, testing and reloading of machines for a given range. Monitoring the course of the technological process, the quality of manufactured products and ensuring the established speed limit. Monitoring the operation of all nodes of the production line and their adjustment. Maintenance equipment. Participation in the preparation of defective statements on overhaul equipment, in the acceptance of equipment after repair. Quality control of semi-finished products and materials. Monitoring the technological process of manufacturing products and their quality indicators in accordance with state standard. Carrying out calculations for the optimal operation of equipment and reducing waste of raw materials.

3. RIGHTS OF THE EMPLOYEE

The employee has the right to:

providing him with a job employment contract;

a workplace that meets the state regulatory requirements for labor protection and the conditions provided for by the collective agreement;

timely and full payment wages in accordance with their qualifications, the complexity of the work, the quantity and quality of the work performed;

rest provided by the establishment of normal working hours, reduced working hours for certain professions and categories of workers, the provision of weekly days off, non-working public holidays paid annual leave;

full reliable information about working conditions and labor protection requirements at the workplace;

vocational training, retraining and advanced training in the manner prescribed by Labor Code Russian Federation and others federal laws;

association, including the right to create trade unions and join them to protect their labor rights, freedoms and legitimate interests;

participation in the management of the organization in the forms provided for by the Labor Code of the Russian Federation, other federal laws and the collective agreement;

conducting collective negotiations and concluding collective agreements and agreements through their representatives, as well as information on the implementation of the collective agreement, agreements;

protection of their labor rights, freedoms and legitimate interests by all means not prohibited by law;

resolution of individual and collective labor disputes, including the right to strike, in accordance with the procedure established by the Labor Code of the Russian Federation and other federal laws;

compensation for harm caused to him in connection with the performance of labor duties, and compensation for moral damage in the manner prescribed by the Labor Code of the Russian Federation, other federal laws;

obligatory social insurance in cases stipulated by federal laws;

obtaining materials and documents related to their activities;

interaction with other divisions of the Employer to resolve operational issues of their professional activities.

4. EMPLOYEE RESPONSIBILITIES

The employee is obliged:

conscientiously fulfill their labor obligations assigned to him by the employment contract and job description;

observe the rules of internal labor regulations;

observe labor discipline;

comply with established labor standards;

comply with the requirements for labor protection and ensuring labor safety;

take care of the property of the Employer (including the property of third parties held by the Employer, if the Employer is responsible for the safety of this property) and other employees;

immediately notify the Employer or immediate supervisor of a situation that poses a threat to the life and health of people, the safety of the Employer's property (including the property of third parties held by the Employer, if the Employer is responsible for the safety of this property).

5. RESPONSIBILITY OF THE EMPLOYEE

The employee is responsible for:

5.1. Failure to fulfill their obligations.

5.2. Inaccurate information about the status of the work.

5.3. Failure to comply with orders, instructions and instructions of the Employer.

5.4. Violation of safety regulations and instructions for labor protection, failure to take measures to suppress the identified violations of safety regulations, fire and other rules that pose a threat to the activities of the Employer and his employees.

5.5. Failure to comply with labor discipline.

6. WORKING CONDITIONS

6.1. The work schedule of the Employee is determined in accordance with the internal labor regulations established by the Employer.

6.2. In connection with the production need, the Employee is obliged to go on business trips (including local ones).

6.3. Characteristics of working conditions at the workplace: ____________________.

(option:

6.4. The Employee is familiar with the Employer's regulation on official and commercial secrets and undertakes not to disclose it.)

6.5. _______________________________________________________________. (additional conditions that do not worsen the position of the employee in comparison with those established by labor legislation and other regulatory legal acts containing norms labor law, collective agreement, agreements, local regulations)

7. RELATIONSHIPS (LINKS BY POSITION)

8. ASSESSMENT OF THE WORKER'S PERFORMANCE AND RESULTS OF THEIR WORK

8.1. The criteria for evaluating the business qualities of an Employee are:

qualification;

work experience in the specialty;

professional competence, expressed in best quality work performed;

the level of labor discipline;

labor intensity (ability to short time cope with a large amount of work);

ability to work with documents;

ability to learn in a timely manner technical means that increase labor productivity and quality of work;

work ethics, communication style;

ability to be creative, entrepreneurial;

ability to adequate self-assessment;

manifestation of initiative in work, performance of work of higher qualification;

increase in individual production;

rationalization proposals;

practical assistance to newly hired employees without fixing mentoring by the relevant order;

high work culture in a particular workplace.

8.2. The results of the work and the timeliness of its implementation are evaluated according to the following criteria:

the results achieved by the Employee in the performance of duties stipulated by the job description and the employment contract;

the quality of the finished work;

timeliness of performance of official duties;

fulfillment of normalized tasks, the level of labor productivity.

8.3. Evaluation of business qualities and results of work is carried out on the basis of objective indicators, a motivated opinion of the immediate supervisor and colleagues.

The job description was developed on the basis of the Unified Tariff and Qualification Directory of Works and Professions of Workers. Issue 41

Head of the structural unit: _______________________ _________ (full name) (signature) "___" ________ ____ Agreed: legal service _______________________ _________ (full name) (signature) "___" ________ ____ with instructions familiarized with: (or: received instructions) _________ _________ (full name) (signature) "___" ________ ____

APPROVE:

________________________

[Job title]

________________________

________________________

[Name of company]

________________/[FULL NAME.]/

"____" ____________ 20__

JOB DESCRIPTION

Adjuster of forging and pressing equipment of the 6th category

1. General Provisions

1.1. This job description defines and regulates the powers, functional and job duties, rights and responsibilities of the adjuster of forging and pressing equipment of the 6th category [Name of organization in the genitive case] (hereinafter referred to as the Company).

1.2. The adjuster of the forging and pressing equipment of the 6th category is appointed to the position and dismissed from the position in accordance with the procedure established by the current labor legislation by order of the head of the Company.

1.3. The adjuster of the forging and pressing equipment of the 6th category belongs to the category of workers and reports directly to [position title of the immediate supervisor in the dative case] of the Company.

1.4. Adjuster of forging and pressing equipment of the 6th category is responsible for:

• timely and high-quality performance of tasks for their intended purpose;
• compliance with performance and labor discipline;
• observance of labor safety measures, maintenance of order, compliance with fire safety rules at the work site (workplace) entrusted to him.

1.5. A person with a secondary vocational education in this specialty and work experience of at least 1 year is appointed to the position of an adjuster of forging and pressing equipment of the 6th category.

1.6. In practice, the fitter of forging and pressing equipment of the 6th category should be guided by:

• local acts and organizational and administrative documents of the Company;
• internal labor regulations;
• rules of labor protection and safety, ensuring industrial sanitation and fire protection;
• instructions, orders, decisions and instructions of the immediate supervisor;
• this job description.

1.7. The adjuster of the forging and pressing equipment of the 6th category must know:

• device and kinematic diagrams of complex hammers, presses, device of complex stamps;
• rules and basic conditions for performing operations on forging complex forgings, stamping complex parts;
• design, kinematic diagrams of automatic and semi-automatic lines;
• methods of adjustment, repair and installation of equipment.

1.8. During the period of temporary absence of the adjuster of forging and pressing equipment of the 6th category, his duties are assigned to [name of the position of the deputy].

2. Job responsibilities

Adjuster of forging and pressing equipment of the 6th category performs the following labor functions:

2.1. Adjustment, installation and regulation of forging multi-strand dies for complex forgings.

2.2. Adjustment and regulation of the work of forging and stamping hammers with a mass of falling parts over 8 tons, mechanical and hydraulic forging presses with a force of over 50 MN (5000 tf), horizontal bending presses (bulldozers) with a force of over 3 MN (300 tf).

2.3. Adjustment, installation and regulation of the operation of dies and horizontal forging machines with a force of more than 12 MN (1200 tf).

2.4. Adjustment of mills for cross-rolling balls with electric heating, rolling machines for rolling rings for ball bearings.

2.5. Adjustment of gear rolling mills various types for rolling teeth on heated workpieces.

2.6. Adjustment of automatic and semi-automatic lines for hot stamping of complex parts and products.

2.7. Adjustment and regulation of manipulators (robots) with program control.

2.8. Adjustment and installation of tools on bolt-forging and nut-punching presses. Assembly, disassembly, installation and debugging of complex stamps.

2.9. Checking the correctness of the adjustment made.

In case of official necessity, the adjuster of the forging and pressing equipment of the 6th category may be involved in the performance of duties overtime, in the manner prescribed by law.

3. Rights

Adjuster of forging and pressing equipment of the 6th category has the right to:

3.1. Get acquainted with the draft decisions of the management of the enterprise relating to its activities.

3.2. Submit proposals for the management to improve the work related to the responsibilities provided for in this job description.

3.3. Notify the immediate supervisor of any deficiencies identified in the course of the performance of their duties in production activities enterprise (its structural subdivisions) and make proposals for their elimination.

3.4. Request personally or on behalf of the immediate supervisor from the heads of enterprise departments and specialists information and documents necessary for the performance of their duties.

3.5. Involve specialists from all (separate) structural divisions of the Company in solving the tasks assigned to him (if it is provided for by the regulations on structural divisions, if not, with the permission of the head of the Company).

3.6. Require the management of the enterprise to assist in the performance of their duties and rights.

4. Responsibility and performance evaluation

4.1. The fitter of forging and pressing equipment of the 6th category bears administrative, disciplinary and material (and in some cases, provided by law RF, - and criminal) responsibility for:

4.1.1. Non-fulfillment or improper fulfillment of official instructions of the immediate supervisor.

4.1.2. Failure or improper performance of labor functions and the tasks assigned to him.

4.1.3. Unlawful use of the granted official powers, as well as their use for personal purposes.

4.1.4. Inaccurate information about the status of the work entrusted to him.

4.1.5. Failure to take measures to suppress the identified violations of safety regulations, fire and other rules that pose a threat to the activities of the enterprise and its employees.

4.1.6. Failure to enforce labor discipline.

4.2. Evaluation of the work of the fitter of forging and pressing equipment of the 6th category is carried out:

4.2.1. The immediate supervisor - regularly, in the course of the daily implementation by the employee of his labor functions.

4.2.2. Attestation Commission of the enterprise - periodically, but at least once every two years based on the documented results of the work for the evaluation period.

4.3. The main criterion for evaluating the work of an adjuster of forging and pressing equipment of the 6th category is the quality, completeness and timeliness of his performance of the tasks provided for in this instruction.

5. Working conditions

5.1. The mode of operation of the 6th grade forging and pressing equipment adjuster is determined in accordance with the internal labor regulations established by the Company.

5.2. In connection with the production need, the adjuster of the forging and pressing equipment of the 6th category is obliged to go on business trips (including local ones).

Acquainted with the instruction __________ / ____________ / "____" _______ 20__

Test equipment adjuster-installer (electronics) is a worker who performs installation, commissioning, regulation and commissioning of test equipment.

Depending on the category, the adjuster-installer of test equipment can perform simple or more complex work:

• Adjustment and regulation of simple radio-electronic units of test equipment. Installation of individual nodes, connections, devices and blocks of medium complexity according to the wiring diagram with complete termination of conductors and connections. Cutting multi-wire armored cables in a rubber sheath with termination of the ends in the blocks. Production of all kinds of harnesses from wires of various brands according to templates. Unsoldering of simple circuits of repaired devices with installation and soldering of replaceable parts and assemblies. Electrical and mechanical adjustment and regulation, verification and testing of electrical measuring equipment of medium complexity, as well as balancing of the mobile system of instruments. Regulation of the main power sources. Identification and elimination of mechanical and electrical faults during adjustment and testing. Identification of defects in mounted circuits and their elimination. Testing and ringing of mounted circuits with electrical measuring instruments, finding defects and their elimination. Test of resistance and insulation of conductors. Establishing the sequence of installation of circuits.
• Adjustment and regulation of radio-electronic units of test equipment of medium complexity. Establishment of optimally permissible operating modes of equipment and monitoring their stability. Finding damage in interblock connections and elements of the microwave path of measuring stands. Installation of equipment of medium complexity according to the wiring diagram and simple experimental devices according to the concept diagram with the implementation of various assembly, termination and cable work. Making circuits for experimental devices and apparatuses from various conductors, cables, tires and testing them with various electrical measuring instruments. Unsoldering and sealing of devices, blocks, assemblies, circuits and production of circuit diagrams and wiring diagrams for knitting circuits. Drawing up wiring diagrams and artificial lines. Cutting and soldering of all kinds of conductors, cables and tires. Simple calculations of resistance in various links of the circuit, testing of resistance and insulation of conductors. Electrical and mechanical regulation, testing, verification of complex electrical measuring equipment. Identification of various problems during installation, finding places of damage and eliminating them by replacing nodes and parts of the circuit, followed by a test under current. Measurement of electrical characteristics in accordance with the control and measuring instructions.
• Adjustment and regulation of radio-electronic units of test equipment and computers of increased complexity. Adjustment of equipment for partial testing of color kinescopes. Installation of large groups of varying complexity of radio-electronic devices, instruments and apparatuses included in the overall wiring diagram. Installation of experimental samples according to sketches and schematic diagrams. Production without samples of circuits from various conductors, cables, tires and radio components. Testing circuits with various electrical measuring instruments. Production according to circuit diagrams and wiring diagrams of templates for knitting circuits with compact placement of conductors and in compliance with technical requirements by setting them up. Drafting of schematic diagrams based on product samples. Drawing up wiring diagrams and artificial lines. Calculations of resistance in various links of the circuit, testing of resistance and insulation of conductors. Electrical and mechanical regulation, verification, testing of complex electrical equipment. Regulation of switch instruments and devices of various systems and degrees of accuracy. Software troubleshooting on test and measuring equipment. Production, adjustment of individual boards for radio-electronic devices to replace those that have become unusable. Run control programs during commissioning of measuring equipment. Control tests and delivery of radio-electronic units with a demonstration of the operation of devices and entire installations according to the general scheme during commissioning. Preventive work on test and measuring equipment.
• Installation, adjustment and regulation of radio-electronic units of test equipment, computer equipment, test equipment for color kinescopes. Installation, adjustment and operation of test signal sensors (monoscopic installations, slide projectors, film projectors, mono projectors, color stripe generators). Troubleshooting and troubleshooting with the help of control tests in programmable pulse generators and voltage sources, counters, registers on a discrete element base and using integrated circuits. Comprehensive adjustment and launch of individual complex blocks in measuring systems. Full check and delivery to the receiver of electrical measuring equipment of any complexity. Calculation of electrical circuits to determine the parameters of radio components of mounted circuits. Control tests of mounted units and radio installations during commissioning.
• Installation, adjustment and regulation of radio-electronic units of test equipment and computer technology of increased complexity and automation devices on a radio-electronic base with subsequent repair and adjustment. Installation, adjustment, testing, repair and commissioning of industrial automation circuits, telemechanics, communications, contact, relay, electromagnetic, ionic and semiconductor electric drive control circuits. Diagnostics of equipment control systems using special test programs and stands using computer technology. Drawing up test and adjustment of technological programs for control and measurement and special technological equipment. Analysis and systematization of failures in the operation of technological equipment.
• Installation, adjustment, regulation and commissioning of complex control systems, equipment based on microprocessor technology with the performance of all types of restoration and repair work of elements of these systems, programmable controllers, micro- and mini-computers and other computer equipment. Installation and adjustment of equipment for testing color kinescopes using impulse stabilizers and special scanning devices. Installation, adjustment and operation of samples of unique domestic and foreign equipment with automatic control technological processes, with electronic circuits. Participation in the development of non-standard test equipment, installation of blocks and testing them for performance.

Unified Tariff and Qualification Directory of Works and Professions of Workers (ETKS), 2019
Issue №20 ETKS
The issue is approved by the Decree of the Ministry of Labor of the Russian Federation of January 21, 2000 N 5
(as amended by the Decree of the Ministry of Labor of the Russian Federation of September 12, 2001 N 67)

Test equipment installer

§ 48. Adjuster-installer of test equipment of the 3rd category

Job Description. Adjustment and regulation of simple radio-electronic units of test equipment. Installation of individual nodes, connections, devices and blocks of medium complexity according to the wiring diagram with complete termination of conductors and connections. Cutting multi-wire armored cables in a rubber sheath with termination of the ends in the blocks. Production of all kinds of harnesses from wires of various brands according to templates. Unsoldering of simple circuits of repaired devices with installation and soldering of replaceable parts and assemblies. Electrical and mechanical adjustment and regulation, verification and testing of electrical measuring equipment of medium complexity, as well as balancing of the mobile system of instruments. Regulation of the main power sources. Identification and elimination of mechanical and electrical faults during adjustment and testing. Identification of defects in mounted circuits and their elimination. Testing and ringing of mounted circuits with electrical measuring instruments, finding defects and their elimination. Test of resistance and insulation of conductors. Establishing the sequence of installation of circuits.

Must know: methods for determining faults; installation of simple radio-electronic units and operational installation of complex products with conductors of various sections; the principle of operation of mounted mechanisms and devices; conventions devices and components in the wiring diagram in general; installation and circuit diagrams of medium complexity; basic information on electrical engineering of alternating and direct currents within the scope of the work performed; mechanical and electrical properties of conductors and insulating materials used during installation; the purpose and arrangement of measuring and electrical measuring instruments used to check the polarity, breaks and short circuits in the mounted circuit; methods for including mounted elements in the control and test network; methods of setting the applied measuring equipment; methods of mechanical and electrical adjustment of electrical measuring equipment of medium complexity; rules for using and connecting them to regulated instruments and devices; installation and soldering requirements.

Work examples

1. Power supplies for klystrons, pumping stations, measurement stand electrical parameters TWT, impulse shaping amplifiers, etc. - installation, repair, adjustment.

2. Amplification unit of the magnetic induction meter - installation.

3. Capacitor blocks - tuning and electrical regulation.

4. Full-wave rectifiers - installation and testing.

5. Low-frequency generators GZ-3b, GZ-33, GCh-31 - replacement of lamps and semiconductor devices; finding and troubleshooting in the generator unit.

6. Sound generators - step-by-step electrical check and regulation.

7. Resistive-capacitive voltage divider for pulse signals of microsecond and millisecond duration - installation and configuration.

8. Measuring complexes based on computers - daily Maintenance.

9. Electromechanical meters - step-by-step regulation.

10. Power supplies of all types, sound generators, thermoionization vacuum gauges, tube voltmeters - repair and regulation.

11. Heat chambers DR-164 - setting the thermal regime; regulation of the fan drive unit; heater replacement.

12. Electrical measuring mechanisms of classes 1 - 2, 5 - balancing.

13. Non-standardized devices for measuring R, L, C - setting.

14. Oscilloscopes - simple repair, adjustment.

15. Test equipment for OS, fuel assemblies, power transformers and chokes - maintenance; elimination of minor faults and control of parameters.

16. Test equipment - checking electrical circuits, test connectors; repair of RSH type connectors.

17. Printed circuit boards (modules) - desoldering microcircuits, checking their functioning; identification of faulty elements and their replacement.

18. Electrical measuring instruments - verification with the connection of a reference stand; change of electrical measuring instruments; magnetization and remagnetization of magnets.

19. Instruments of thermoelectric system, power supplies of all types, sound generators, thermoionization vacuum gauges, tube voltmeters - repair and regulation.

20. Prefixes to the characterograph - installation and adjustment.

21. Potentiometer - installation.

22. Relay circuits of high-frequency transmitters - electrical regulation.

23. Special equipment - regulation of nodes and blocks.

24. Measuring stand locking system - check and installation.

25. Bridge circuits for measuring R, L, C - setting.

26. Test benches - assembly of individual units and blocks, verification, adjustment.

27. Pollution control unit UZK-1 - control setting and repair of electronic account.

28. Installation for measuring the volt-capacitive characteristic ZhKM 346.001 - adjustment and regulation of the comparator and threshold discriminator.

29. Installation of burning by periodic pulses - repair, adjustment.

30. Installation for testing static parameters - repair of cathode, grid and anode circuits.

31. Impulse magnetizing installation - adjustment.

32. Switching circuits - repair, preventive maintenance, replacement of relays, keys, toggle switches, installation equipment.

33. Electric motors - collector cleaning, lubrication, motor change; connection to the installation and running.

§ 49. Adjuster-installer of test equipment of the 4th category

Job Description. Adjustment and regulation of radio-electronic units of test equipment of medium complexity. Establishment of optimally permissible operating modes of equipment and monitoring their stability. Finding damage in interblock connections and elements of the microwave path of measuring stands. Installation of equipment of medium complexity according to the wiring diagram and simple experimental devices according to the concept diagram with the implementation of various assembly, termination and cable work. Making circuits for experimental devices and apparatuses from various conductors, cables, tires and testing them with various electrical measuring instruments. Unsoldering and sealing of devices, blocks, assemblies, circuits and production of circuit diagrams and wiring diagrams for knitting circuits. Drawing up wiring diagrams and artificial lines. Cutting and soldering of all kinds of conductors, cables and tires. Simple calculations of resistance in various links of the circuit, testing of resistance and insulation of conductors. Electrical and mechanical regulation, testing, verification of complex electrical measuring equipment. Identification of various problems during installation, finding places of damage and eliminating them by replacing nodes and parts of the circuit, followed by a test under current. Measurement of electrical characteristics in accordance with the control and measuring instructions.

Must know: methods for identifying typical malfunctions of test equipment and installation of radio-electronic equipment; assembly and circuit diagrams of group connections of devices and devices included in the assembly diagram; rules for connecting circuits, installing parts and devices, the sequence of their inclusion in the overall circuit; technological and electrical properties of various conductive and insulating materials used during installation; principle of operation and purpose of control and measuring and auxiliary equipment (avometer, generators, voltmeters, oscilloscope, etc.); purpose and use of the mounting tool; power supply connection diagram when assembling circuits; fundamentals of electrical engineering, radio engineering, impulse technology; device and principle of operation of the tested circuit; methods for testing micromodules using maps of resistance, voltage, and electrical parameters.

Work examples

1. Automatic machines (type U-701, U-705, U-706, UPS, PRS, GP-5) - regulation by electrical parameters.

2. Automatic measurement of statistic parameters 261.0061 - regulation of the unit for supplying diodes to contact pads; repair of threshold devices.

3. Automatic packaging machines for microcircuits in loading boards - repair and adjustment.

4. Automatic classification 2.650.050/09 - regulation of the mechanism for supplying devices to contacting devices; repair and adjustment of the measuring channel.

5. Ammeters, voltmeters - regulation and verification.

6. Glow power supply with voltage stabilization - assembly and testing.

7. Relay and control units - installation.

8. Control relay blocks for high-voltage rectifiers up to 50 W - installation and adjustment.

9. Scanners for testing cathode ray tubes - medium repair.

10. Lamp microammeter block - installation, adjustment.

11. Stationary dual-range quartz generators powered by rectifiers - electrical regulation.

12. Sawtooth voltage generator - setting.

13. Mode setters for integrated circuits and micromodules - installation, adjustment.

14. Pulse sensors, indicators and course graphs - regulation.

15. Frequency divider on logic elements or triggers of integral design - installation and configuration.

16. Power supplies built on the principle of using chokes with saturation - installation and commissioning.

17. Stabilized high-voltage power supplies - repair.

18. Climatic non-contact control chamber - adjustment and repair.

19. Heat chambers 12 KTS, KTS-M - repair and adjustment.

20. V6-1, V1-4 tube voltmeter calibrators and V3-24 type tube voltmeters - repair and adjustment of the alternating voltage generator unit.

21. Thermal cycling chambers KTC-0.025 - setting temperature conditions and repairing the electrical circuit.

22. Semi-automatic coercimeter - setting.

23. Ruler for assembling and adjusting reversible periodic systems - setting.

24. Mechanisms of time, software, arresting - regulation.

25. Equipment for tuning semiconductor devices - adjustment and regulation.

26. Mounting and welding equipment (relay blocks, resistance boxes, current regulators and starting devices) - adjustment.

27. Equipment for ETT, including USTT - 0.25 s. thermotracers 1609 - repair, adjustment.

28. Electronics-100 printed circuit boards, alarm register, analog signal converter, switching register, indication blocks, fixing switching levels, logarithmic current converter, sweep generator - simple repair, regulation, adjustment, installation.

29. Devices of the magnetoelectric system of class 0.2 - 1.5, combined devices of the type "C" and "TT", bridges and resistance boxes, amplifiers general purpose- repair, adjustment, alignment.

30. High-frequency switches of various types, waveguide and coaxial couplers, thermistor heads and ballometers - checking and regulation.

31. Measuring receiver - repair.

32. Devices with a Hall sensor - installation and adjustment.

33. Measuring systems such as digital voltmeter, digital printer, perforator, comparator and code converter - installation and configuration.

34. Systems for automatic temperature maintenance of furnaces - repair and adjustment.

35. Electronic stabilizers of direct and alternating current with a power of up to 300 W - installation, adjustment, repair.

36. Stand for carrying out climatic and mechanical tests, stands for current training - repair and adjustment.

37. Stand for setting modes UNTM / D - checking the sources of the right current and reverse voltage; setting the temperature setting block; bringing the stand to thermal and electrical modes.

38. Stand for panoramic measurement of TWT parameters - repair.

39. Test benches for group testing of OS, TVS, line-scan tube circuits - adjustment, troubleshooting, parameter control.

40. Schemes of simple stabilized power supplies - manufacturing, regulation.

41. Schemes for measuring static parameters, reverse currents - adjustment, repair.

42. Schemes for testing micromodules at extreme temperatures (+70 degrees C and -40 degrees C) - assembly, repair, adjustment.

43. Trigger circuits - adjustment.

44. Thyristor voltage regulators - repair.

45. Installations for measuring reverse currents - repair, adjustment.

46. ​​Installations for measuring the parameters of semiconductor devices, testing transistors for heat and cold resistance, thermal cycling installations - adjustment, repair.

47. Installation for testing semiconductor devices at elevated and reduced pressure - preventive maintenance, adjustment.

48. Installation for testing the wettability of the leads of semiconductor devices with solder POS-40, POS-60 - adjustment, preventive maintenance.

49. Installations for tightness control "dry method" UKGE - repair, adjustment.

50. Vibrating, shock, mounting installations - repair, adjustment.

51. TTL-490 switching charge measurement settings - calibration setting by reference capacities and regulation of a long pulse edge.

52. Installations for measuring the resistance of the detector at the zero point, capacitance, quality factor - repair, adjustment.

53. Characterograph - adjustment.

54. Digital measuring instruments such as Shch4312, ChZ-30, "I2-19, ChZ-24 - identifying and eliminating faults in one of the blocks of counting decades; checking the circuit of logical operations.

55. Electric generator type ZGDA - installation and adjustment.

§ 50. Adjuster-installer of test equipment of the 5th category

Job Description. Adjustment and regulation of radio-electronic units of test equipment and computers of increased complexity. Adjustment of equipment for partial testing of color kinescopes. Installation of large groups of varying complexity of radio-electronic devices, instruments and apparatuses included in the overall wiring diagram. Installation of experimental samples according to sketches and schematic diagrams. Production without samples of circuits from various conductors, cables, tires and radio components. Testing circuits with various electrical measuring instruments. Manufacture according to the circuit diagrams and wiring diagrams of templates for knitting circuits with compact placement of conductors and in compliance with the technical requirements for laying them. Drafting of schematic diagrams based on product samples. Drawing up wiring diagrams and artificial lines. Calculations of resistance in various links of the circuit, testing of resistance and insulation of conductors. Electrical and mechanical regulation, verification, testing of complex electrical equipment. Regulation of switch instruments and devices of various systems and degrees of accuracy. Software troubleshooting on test and measuring equipment. Production, adjustment of individual boards for radio-electronic devices to replace those that have become unusable. Run control programs during commissioning of measuring equipment. Control tests and delivery of radio-electronic units with a demonstration of the operation of devices and entire installations according to the general scheme during commissioning. Preventive work on test and measuring equipment.

Must know: methods for identifying various faults and methods for installing complex radio-electronic installations, measuring equipment and objects with a large number of incoming devices and devices with independent circuits; all kinds of assembly and schematic diagrams of group connections of devices and devices; the appointment of individual devices, units included in the mounted circuit; the principle of operation of various devices and radio tubes included in the mounted circuit; test methods for group connections of devices and devices mounted in a common circuit; rules for setting up and adjusting various radio measuring devices, testing and measuring equipment, the procedure and sequence for laying the installation; purpose and rules for shielding conductors and individual links; fundamentals of electrical engineering, radio engineering and impulse technology; rules for setting up and regulating various electrical measuring instruments.

Work examples

1. Units for measuring the electrical parameters of devices - repair, adjustment, performance check.

2. Akulov anisometer - setting.

3. Automatic machines with complex kinematic and electrical circuits - adjustment and repair.

4. Computer and stationary equipment - regulation of nodes and blocks.

5. Blocks with electromagnetic, eccentric mechanisms - regulation.

6. Non-contact regulation blocks on thyristor circuits, control and power blocks for reliability testing, logic blocks - adjustment, repair, installation.

7. Blocks of high-voltage stabilized power supplies - adjustment.

8. Stabilized rectifiers - setting and testing.

9. Vibrating stand VU 10/3000 - setting up the generator, balancing the dynamic coil of the vibrating table; calibration of the stand with checking the frequency and acceleration.

10. Frequency dividers - regulation.

11. Dynamic parameters meter - repair and tuning of the high-frequency unit.

12. Measuring systems like "Viaduct", "Integral" - setting.

13. PK-5003, PK-5005 through passage chambers, control units - temperature control, adjustment, regulation, repair.

14. Semi-automatic classifier - adjustment, repair.

15. Ruler for assembling and adjusting periodic focusing systems, slope gauges - setting.

16. Measuring lines - adjustment, check, repair.

17. Probe manipulators "Zond-A4", "Zond-A5", "EM-680", "EM-6010", "EM-6020" - check, adjustment, repair.

18. Mechanisms with synchronous and monitoring devices - regulation.

19. Electronic microscope, mass spectrometers, thermal cycling units, plasma photometers PFM adjustment.

20. Individual blocks and assemblies that are part of installations or conveyor lines for training and testing the parameters of electrovacuum devices (simulators, reamers, electronic galvanometers, instrumentation amplifiers, low-frequency and high-frequency low power generators, comparators, devices and automation equipment, etc. ) - installation and commissioning.

21. Measuring instruments - adjustment of optics, thread replacement, balancing.

22. Corrective devices and software devices - regulation; electrolytic bath pantograph - adjustment.

23. Semi-automatic contacting and sorting PKRM-2 - setting up the kinematic and electronic circuit; regulation of coordination nodes.

24. Devices containing voltage radiation converters, a digital register, an analog-to-digital converter, a unit for automatically changing the conversion limits - installation and configuration.

25. Devices containing scale converters, multipliers, amplitude detectors and analog signal recorders - installation and configuration.

26. Devices of any complexity, IVIS parameters and durability stands, IVIS power and ignition devices, devices for high-speed photography - repair, installation, adjustment.

27. Control panels and devices - installation, adjustment, repair.

28. Tracking systems, special equipment - regulation.

29. Static installations - installation, adjustment.

30. Stand for panoramic measurement of TWT parameters, stands for functional control, functioning blocks - adjustment, repair, installation, commissioning.

31. Bench of service life UNTIS-1 - adjustment of power supply units and temperature setting unit; regulation of pulse duration and generators.

32. Assembly and welding tables of the SSP-2 type - repair, installation and adjustment.

33. Horizontal scanning circuits (tube and semiconductor) for OS and TVS testing - installation and configuration, troubleshooting.

34. Complex schemes and stands for group testing and measuring the parameters of power transformers and chokes, including those for special purposes - manufacturing, tuning and troubleshooting.

35. Schemes and stands for measuring the electrical characteristics of VIS sources - installation and configuration.

36. Scheme of automatic control of the heat chamber, schemes for testing micromodules for special purposes - installation, adjustment, repair.

37. Thermobaric chambers KHTB-0.16 - setting the chamber to elevated temperature (+125 degrees C) and negative temperatures (-60 degrees C), to work at a pace at reduced pressure.

38. Installation for testing semiconductor devices, microcircuits, installations "Zond-1A" and "Zond-A4" - check, adjustment, repair.

39. Installations for measuring high-frequency parameters of semiconductor devices and microcircuits - checking, tuning, repair.

40. Installations for capacitor welding "Wakwell", "Fesd", "MTK-8002", installation for monitoring test parameters of microcircuits based on the meter "EM-640" - repair and adjustment.

41. Installations, stands of test vibration electrodynamic - repair and adjustment.

42. Mechanical impact testing machines - adjustment.

43. Functional nodes on integrated circuits such as a differential amplifier, an analog adder, an integrator, a voltage-to-frequency converter, a register, a comparator of analog signals - installation and configuration.

44. Settings for measuring conversion losses, triode parameters, setting pulse training - repair, tuning.

45. Installations (stands) for testing electrovacuum devices for durability - complex adjustment.

46. ​​Voltage and power amplifiers for various purposes, oscilloscope amplifiers - installation and adjustment.

47. Installation of a test for durability - complex adjustment.

§ 51. Adjuster-installer of test equipment of the 6th category

Job Description. Installation, adjustment and regulation of radio-electronic units of test equipment, computer equipment, test equipment for color kinescopes. Installation, adjustment and operation of test signal sensors (monoscopic installations, slide projectors, film projectors, mono projectors, color stripe generators). Troubleshooting and troubleshooting with the help of control tests in programmable pulse generators and voltage sources, counters, registers on a discrete element base and using integrated circuits. Comprehensive adjustment and launch of individual complex blocks in measuring systems. Full check and delivery to the receiver of electrical measuring equipment of any complexity. Calculation of electrical circuits to determine the parameters of radio components of mounted circuits. Control tests of mounted units and radio installations during commissioning.

Must know: methods for detecting faults in radio-electronic units of complex test equipment and computer technology; methods of mounting electronic units, samples of devices and devices according to sketches and circuit diagrams; calculation of circuits and power supplies; the laws of construction of various assembly and circuit diagrams; purpose and practical application of measuring instruments and devices; principle of fault detection of electrical parameters and waveforms; forms and parameters of signals in radio-electronic equipment; the impact of interference on the shape and parameters of signals; technical conditions and requirements for the installation of equipment and instruments.

Requires secondary vocational education.

Work examples

1. Analyzers, information-measuring systems installation, adjustment.

2. Power measurement units on the VHF band, functional blocks of computer technology - repair, adjustment.

3. Blocks of breakdown counters - installation, configuration.

4. High-frequency, high-voltage stabilized rectifiers with a voltage of 60,000 V - adjustment.

5. Quantum optical generators of the microwave type - adjustment and repair.

6. Complexes and measuring lines (such as "Integral", Elikon", "Viaduct", etc.) - adjustment, calibration, verification, repair.

7. Modulators of all types - repair and adjustment.

8. Model electric mesh type MSM - setting.

9. Pumping posts with program control - adjustment.

10. Devices for measuring the electrical characteristics of gas-discharge laser pump lamps - installation and adjustment.

11. Devices of the electrostatic system (C), digital type Shch-1413, candle meters, photometers - repair, calibration, regulation.

12. Stand for dynamic testing of pulsed TWTs of high power - installation, adjustment, repair.

13. Schemes for measuring impulse parameters, for checking the operation of installations - adjustment.

14. Complex schemes and stands for measuring the electrical and light characteristics of VIS sources - installation, adjustment.

15. Complex schemes and stands for group tests and measurements of electrical parameters of OS, fuel assemblies and micromodules of all ratings, including special-purpose ones - adjustment, control over their operation, repair.

16. Schemes for checking electrical parameters and testing at various conditions environment- installation, regulation, adjustment.

17. Amplifiers of high and low frequency, intermediate frequency (multi-stage), amplifiers direct current(multi-stage) - installation, commissioning and regulation.

18. Installations for measuring noise of high-frequency diodes - installation and adjustment.

19. Amplifiers, generators, highly stable power supplies, automatic circuits - installation, regulation, tuning.

20. Amplifying devices with an output power of 3 kW or more - adjustment, repair.

21. Installations for automatic recording of the hysteresis loop, topography of the magnetic field of complex magnetic systems - installation and adjustment.

22. Installations for dynamic and climatic testing of generator pulsed and stroboscopic lamps - repair and adjustment.

23. Installations for measuring static and dynamic parameters of electrovacuum devices, for measuring pulse parameters of semiconductor devices and microcircuits - adjustment, calibration, verification, repair.

24. Installations for thermocompression welding EM-424A., MS-41P2, argon-arc welding type URS-3 - repair and adjustment.

25. Installations potentiometric type U-302, U-309, potentiometers R-307, R2/1; galvanometers; pulse multichannel generators; high-speed oscilloscopes with a bandwidth above 25 MHz; storage oscilloscopes; devices for measuring time and frequency - repair, adjustment, adjustment, installation.

26. Automatic and semi-automatic installations for measuring static and dynamic parameters of reed switches, integrated circuits, microwave semiconductor hybrid circuits - repair and adjustment.

27. Installations for dynamic and climatic testing of reed switches - repair and adjustment.

28. Installations for measuring the noise of reed switches - installation and adjustment.

29. Electron-beam argon purification installations - adjustment.

30. Digital photometers, radiometers, spectroradiometers - installation and adjustment.

31. Centrifuge - repair and adjustment of control circuits.

32. Electrohydrogen furnaces of the type IO570020, AZ6023 - adjustment.

§ 52. Adjuster-installer of test equipment of the 7th category

Job Description. Installation, adjustment and regulation of radio-electronic units of test equipment and computer technology of increased complexity and automation devices on a radio-electronic base with subsequent repair and adjustment. Installation, adjustment, testing, repair and commissioning of industrial automation circuits, telemechanics, communications, contact, relay, electromagnetic, ionic and semiconductor electric drive control circuits. Diagnostics of equipment control systems using special test programs and stands using computer technology. Drawing up test and adjustment of technological programs for control and measuring and special technological equipment. Analysis and systematization of failures in the operation of technological equipment.

Must know: methods for detecting faults in radio-electronic units of complex test equipment and computer technology; methods of installation of experimental models of apparatuses and instruments according to sketches and schematic diagrams; laws of construction and calculation of assembly and circuit diagrams; calculation of electrical circuits to determine the parameters of radio components of mounted circuits; ways of compiling and adjusting technological and test programs; organization of a complex of works on adjustment and troubleshooting of devices and systems of computer technology; device and diagnostics of unique measuring and control systems and complexes.

Requires secondary vocational education.

Work examples

1. Blocks of equipment for measuring non-electric quantities by electrical methods (pressure, acceleration, temperature, geometric dimensions meters; flaw detectors, etc.) - installation, adjustment, repair.

2. Blocks of industrial automation, telemechanics and communications (on a radio-electronic basis) - repair, adjustment.

3. Blocks of spreading devices (non-standard) - repair, adjustment.

4. High-frequency generators (sinusoidal, pulse), quantum optical with automatic mode control units - repair, adjustment, frequency adjustment.

5. Complexes of complex automatic and semi-automatic equipment of various systems - troubleshooting, repair, adjustment.

6. Subblocks of algorithms for automatic thermal protection of X-ray tubes, subblocks for processing a television signal (SOTS) - repair and adjustment.

7. Schemes for testing electrovacuum products and monitoring electrical parameters, including those with climatic chambers - installation, repair, adjustment.

8. Schemes and stands for measuring electrical parameters and characteristics of electro-optical devices - setting and monitoring their work, repair.

9. Installations for automated application of the phosphor on the screens of the image intensifier tube - adjustment, repair.

§ 53. Adjuster-installer of test equipment of the 8th category

Job Description. Installation, adjustment, regulation and commissioning of complex control systems, equipment based on microprocessor technology with the performance of all types of restoration and repair work of elements of these systems, programmable controllers, micro- and mini-computers and other computer equipment. Installation and adjustment of equipment for testing color kinescopes using impulse stabilizers and special scanning devices. Installation, adjustment and operation of samples of unique domestic and foreign equipment with automatic process control, with electronic circuits. Participation in the development of non-standard test equipment, installation of blocks and testing them for performance.

Must know: methods for detecting faults in radio-electronic unique domestic and foreign equipment; methods of building control systems based on microprocessor technology, functional and block diagrams of micro- and mini-computers; a method for setting up control systems in order to obtain the specified characteristics of devices and instruments of converter technology; programming and repair methods for computer-based equipment.

Requires secondary vocational education.

Work examples

1. Scanners for information display devices, mini- and micro-computer monitors and other control systems - adjustment, installation, regulation.

2. Complex blocks based on LSI - repair and adjustment.

3. Measuring complexes with control computers (such as "Ikomat-110", "Ikomat-115", "Viking", etc.) - adjustment, repair, diagnostics.

4. Control and measuring systems and devices with microprocessor control - installation, adjustment, regulation, diagnostics.

5. Conveyor lines and installations for the manufacture of products of electrovacuum and semiconductor production, equipped with program control and automatic systems for maintaining the specified parameters - repair, adjustment.

6. Schemes of experimental measuring devices and complexes - installation, adjustment, repair.

7. Installations for applying thin films of the "Leybold" type, vacuum processing and manufacturing of an image intensifier tube photocathode, magnetic deposition of contact layers - repair, adjustment.