1. Molder of products, structures and building materials 3rd category belongs to the category of workers.

2. For the position of molder of products, structures and building materials of the 3rd category, a person with a secondary education is accepted professional education or primary vocational education and special training and work experience of at least one year.

3. A molder of products, structures and building materials of the 3rd category is hired and dismissed by the director of the organization upon nomination (position).

4. A molder of products, structures and building materials of the 3rd category must know:

a) special (professional) knowledge for the position:

Standards of linear dimensions;

Roll cutting methods;

Forming methods and techniques;

Methods of articulation in raw form of individual parts of an order;

Design and principle of operation of the equipment being serviced;

Methods and rules for laying and tensioning reinforcement;

Technical requirements for manufactured products;

Rules for reading drawings;

Requirements technological maps by molding modes;

Techniques and methods for slinging and moving products;

The range of used facing carpets and tiles and the requirements for their quality;

Rules for assembling and disassembling forms;

The order of filling forms;

Setting times for the mortar and methods for testing blocks and slabs for strength;

Recipe, properties of raw materials and technical specifications for crayons;

Requirements for granules and felt;

Arrangement of molds, pallets, vibration stand;

Rules for stripping products and their installation;

Rules, procedures for cleaning and assembling molds and pallets;

Properties of lubricants;

Forming conveyor performance;

Capacity of distribution hoppers;

Rules and basic techniques for forming asphalt tiles;

b) general knowledge of an employee of the organization:

Rules and regulations of labor protection, safety, industrial sanitation and fire protection,

Rules for the use of personal protective equipment;

Requirements for the quality of work (services) performed, for rational organization labor in the workplace;

Types of defects and ways to prevent and eliminate them;

Production alarm.

5. In his activities, a molder of products, structures and building materials of the 3rd category is guided by:

Legislation of the Russian Federation,

Charter of the organization,

Orders and instructions of the director of the organization,

With this job description,

Internal labor regulations of the organization,

6. A molder of products, structures and building materials of the 3rd category reports directly to a worker with a higher qualification, the head of production (site, workshop) and the director of the organization

7. During the absence of a molder of products, structures and building materials of the 3rd category (business trip, vacation, illness, etc.), his duties are performed by a person appointed by the director of the organization upon presentation in the prescribed manner, who acquires the corresponding rights, duties and is responsible for fulfillment of the duties assigned to him.

II. Job responsibilities

The job responsibilities of a molder of products, structures and building materials of the 3rd category are:

a) Special (professional) job responsibilities:

Carrying out work on forming reinforced concrete products of simple and medium complexity.

Cleaning, lubricating and assembling molds.

Laying ready-made reinforcing mesh, frames and embedded parts into the mold and fixing them in the design position.

Installation of prestressed reinforcement with electrothermal tensioning method, liners and removable dividing panels into molds.

Filling the mold with concrete mixture, leveling and compacting.

Finishing the exposed surfaces of a molded product.

Slinging products and transporting them to heat treatment chambers.

Unmolding of the product with transportation to the finishing post or to the stack.

Controlling the operation of one of the following types of equipment: an installation for electric heating of rods, an installation for cleaning and lubricating molds, a concrete distributor, a concrete paver, a vibrating platform, a trowel, a transfer bridge, a puller, a transferor, a stacker.

A set of individual ceramic tiles in carpets for complex designs or for products with complex profiles.

Forming gypsum boards and blocks on a vibrating platform or under the guidance of a more highly qualified molder on a rotary machine.

Checking the correct assembly, fastening of forms and the quality of the supplied mass.

Molding of expanded clay granules on rollers and belt presses.

Manual molding of cement-sand tiles and crayons.

Performing auxiliary work on molding products from silicate or foam silicate mass of large blocks, facing slabs, etc.

Assembly, installation of forms on trolleys and their disassembly.

Stripping products from molds or pallets, transporting trolleys to the stripping stand.

Vibration stand maintenance.

Dismantling molds, placing products in a stack, on a roller conveyor or other transport equipment.

Cleaning, preparing and assembling molds, pallets, delivering them to the filling site.

Forming asphalt slabs under the guidance of a more highly qualified molder.

Monitoring the filling of dispensing bins with mastic.

Regulating the supply of mastic to the conveyor.

Lubrication of the discharge hopper and tray.

Preparing clay solution and lubricating molds.

Manual molding of asbestos-cement products.

Marking and cutting raw sheets into sizes and configurations in accordance with the order being carried out.

Rolling the workpiece onto a rolling pin and moving it onto the forming table.

Checking the condition of molds, rolling decks and other equipment.

Sorting of defective products.

(Work examples)

Molding:

1. The blocks of internal walls are solid and have partition voids.

2. Foundation blocks of simple configuration.

3. Side stones.

4. Coating and floor slabs are flat.

5. Paving, tram and road slabs.

6. Stair landings.

7. Piles up to 6 m long.

8. Pillars, stepsons, lintels, racks and columns without cantilevers.

9. Steps and treads.

10. Sleepers.)

b) General job responsibilities of an employee of the organization:

Compliance with the internal labor regulations and other local regulations of the organization, internal rules and labor protection, safety, industrial sanitation and fire protection standards.

Execution within employment contract orders of the employees to whom it was repaired in accordance with these instructions.

Performing work on acceptance and delivery of shifts, cleaning and washing, disinfection of serviced equipment and communications, cleaning the workplace, devices, tools, as well as maintaining them in proper condition.

Unified Tariff and Qualification Directory of Works and Professions of Workers (UTKS), 2019
Part No. 2 of Issue No. 40 ETKS
The issue was approved by Resolution of the Ministry of Labor of the Russian Federation dated May 17, 2001 N 41

Molder of products, structures and building materials

§ 268. Molder of products, structures and building materials, 2nd category

Characteristics of work. Performing auxiliary work during the formation of reinforced concrete products and structures. Moving reinforcing mesh, frames, embedded parts and mounting loops and placing them in the mold. Leveling the concrete mixture in a mold using hand tools. Cleaning the sides of the mold from concrete residues. Smoothing open surfaces of molded products. Cleaning unmolded products from flash. Cleaning embedded parts and reinforcement outlets from concrete. Enlarged assembly of facing carpets from standard rugs with selection according to a given color and size. A set of individual ceramic tiles in carpets with a simple pattern for products with simple profiles. Preparation of glue according to a given recipe. Marking products using a stencil or stamp. Molding of gypsum boards and blocks in vacuum boxes. Moving the molding trolley to the mortar mixer or moving the platform with a table under the bucket of the mortar mixer hopper. Filling molds with solution. Moving trolleys and a table with filled forms onto a conveyor. Mandrel of the surface of the product. Periodically checking the slab with a template. Observing the filling and mixing of the mass in the box. Determining the end of evacuation of the plate. Cleaning vacuum boxes and mesh from plaster. Molding of expanded clay granules on rollers and belt presses under the guidance of a more highly qualified molder. Preparing, starting and stopping clay mixers, rollers, presses and other mechanisms. Loading the press, selecting and moving the felt. Moisturizing clay. Performing auxiliary work when forming plasterboard sheets: unpacking, moving rolls with a hoist, installing and securing them; monitoring the uniform flow of the cardboard strip to the forming table and lubricating it with glue; eliminating distortions of the cardboard tape, gluing cardboard in case of breaks. Lubrication of serviced equipment. Molding of asbestos-cement products by hand under the guidance of a more highly qualified molder. Cut raw asbestos-cement sheets according to templates and markings into tiles for ridges and other shaped products using lever scissors, special devices or manually. Laying raw tiles on metal spacer-forms. Sending scraps and raw waste for processing. Dismantling the skate feet at the end of the hardening process. Sorting of defective products.

Must know: requirements of standards and technical specifications for asbestos-cement shaped products in terms of linear dimensions, shape and appearance; methods of joining individual parts of shaped products; basic properties of concrete mixture; rules for transportation of fittings; requirements for the appearance of products; assortment of facing carpets and tiles; quality requirements for tiles, paper, glue and carpets; product labeling; operating principle of the equipment being serviced; rules for starting, stopping and lubrication of serviced equipment; requirements for the quality of molded products; purpose of the tools and devices used.

§ 269. Molder of products, structures and building materials, 3rd category

Characteristics of work. Carrying out work on forming reinforced concrete products of simple and medium complexity. Cleaning, lubricating and assembling molds. Laying ready-made reinforcing mesh, frames and embedded parts into the mold and fixing them in the design position. Installation of prestressed reinforcement with electrothermal tensioning method, liners and removable dividing panels into molds. Filling the mold with concrete mixture, leveling and compacting. Finishing the exposed surfaces of a molded product. Slinging products and transporting them to heat treatment chambers. Unmolding of the product with transportation to the finishing post or to the stack. Controlling the operation of one of the following types of equipment: an installation for electric heating of rods, an installation for cleaning and lubricating molds, a concrete distributor, a concrete paver, a vibrating platform, a trowel, a transfer bridge, a puller, a transferor, a stacker. A set of individual ceramic tiles in carpets for complex designs or for products with complex profiles. Forming gypsum boards and blocks on a vibrating platform or under the guidance of a more highly qualified molder on a carousel machine. Checking the correct assembly, fastening of forms and the quality of the supplied mass. Molding of expanded clay granules on rollers and belt presses. Manual molding of cement-sand tiles and crayons. Performing auxiliary work on molding products from silicate or foam silicate mass of large blocks, facing slabs, etc. Assembly, installation of forms on trolleys and their disassembly. Stripping products from molds or pallets, transporting trolleys to the stripping stand. Vibration stand maintenance. Dismantling molds, placing products in a stack, on a roller conveyor or other transport equipment. Cleaning, preparing and assembling molds, pallets, delivering them to the filling site. Forming asphalt slabs under the guidance of a more highly qualified molder. Monitoring the filling of dispensing bins with mastic. Regulating the supply of mastic to the conveyor. Lubrication of the discharge hopper and tray. Preparing clay solution and lubricating molds. Manual molding of asbestos-cement products. Marking and cutting raw sheets into sizes and configurations in accordance with the order being carried out. Rolling the workpiece onto a rolling pin and moving it onto the forming table. Checking the condition of molds, rolling decks and other equipment. Sorting of defective products.

Must know: standards of linear dimensions; rolling cutting methods; molding methods and techniques; methods of articulation in raw form of individual parts of an order; design and principle of operation of the equipment being serviced; methods and rules for laying and tensioning reinforcement; technical requirements for manufactured products; rules for reading drawings; requirements of technological maps for molding modes; techniques and methods for slinging and moving products; the range of used facing carpets and tiles and the requirements for their quality; rules for assembling and disassembling forms; order of filling forms; setting times for the mortar and methods for testing blocks and slabs for strength; recipe, properties of raw materials and technical specifications for crayons; requirements for granules and felts; arrangement of molds, pallets, vibration stand; rules for stripping products and their installation; rules, procedures for cleaning and assembling molds and pallets; properties of lubricants; productivity of the molding conveyor; capacity of distribution bins; rules and basic techniques for molding asphalt tiles.

Work examples

Molding:

1. The blocks of internal walls are solid and have partition voids.

2. Foundation blocks of simple configuration.

3. Side stones.

4. Coating and floor slabs are flat.

5. Paving, tram and road slabs.

6. Stair landings.

7. Piles up to 6 m long.

8. Pillars, stepsons, lintels, racks and columns without cantilevers.

9. Steps and treads.

§ 270. Molder of products, structures and building materials, 4th category

Characteristics of work. Performing work on molding complex (large-sized, thin-walled) products and structures. Cleaning, lubrication, assembly and alignment of molds and settings. Laying into the mold (installation) of individual elements of the reinforcing frame with enlarged assembly and fixation in the design position. Installation of embedded parts and mounting loops. Installation of prestressed reinforcement into molds using electrothermal or mechanical (using jacks) tension method. Installation of liners, cores and dividing panels. Filling the mold with concrete mixture, leveling and compacting the mixture by vibration. Grouting of exposed surfaces of molded products. Slinging the product and delivering it to the place of heat treatment. Unmolding of the product after heat treatment with transportation to the finishing post or to the stack. Control of the operation of vibrating stamps, centrifuges, as well as units and equipment performing several different operations. Forming asphalt slabs on a molding conveyor. Starting and regulating the uniform supply of mastic. Monitoring the quality of products. Cutting mastic to give the briquettes the required shape. Collecting asphalt chips and moving them to a designated area. Participation in the repair of serviced equipment. Forming gypsum boards, blocks and cement-sand tiles using machines of various designs. Regulating the speed of the machine. Molding of products from silicate or foam silicate mass. Forming plasterboard sheets on a molding conveyor under the guidance of a more highly qualified molder. Leveling gypsum dough on a conveyor belt, removing foreign impurities and lumps of gypsum. Filling the edge with gypsum mass. Adjustment of the edge bending device. Participation in repairs and adjustments of serviced equipment.

Must know: design and principle of operation of serviced machines and installations; methods, rules for laying and tension of reinforcement; technical requirements for manufactured products; rules for reading drawings; requirements of technological maps for molding modes; arrangement of serviced equipment; methods for regulating the molding speed; state standards and technical specifications for manufactured products; rules for adjustment of serviced equipment; technical specifications for plasterboard sheets; methods of regulating the speed of the machine; composition of the molding mass; setting time of gypsum mortar; rules for eliminating minor malfunctions in the operation of serviced equipment.

Work examples

Molding:

1. Single-pitch rafter beams, foundation and framing beams, crossbars, purlins.

2. Foundation blocks of complex configuration.

3. Fences and fences.

4. Columns with consoles and shelves of all types, except two-branch crane ones.

5. Structures for lining metro tunnels, transport intersections and walk-through collectors, used in open-pit construction.

6. Flights of stairs are flat and ribbed.

7. Supports contact networks, power lines and lamps.

8. Panels and blocks of external walls.

9. Floor and covering panels, interior wall panels, cassette and rolled parts.

10. Airfield slabs.

11. Balcony and cornice slabs, loggia fencing panels, entrance canopies, parapet stones.

12. Piles over 6 m long, sheet piling.

13. Non-pressure pipes of all sizes.

§ 271. Molder of products, structures and building materials, 5th category

Characteristics of work. Forming plasterboard sheets on a molding conveyor. Checking the correct dosage of components, the concentration of the sulfide-alcohol stillage solution and the quality of the gypsum test. Ensuring the specified operating mode of the gypsum mixer and molding conveyor. Regulation of cardboard cutting. Observation of filling the edges with gypsum dough. Adjusting the width and thickness of plasterboard sheets. Checking the drying mode and quality of plasterboard sheets. Keeping journal entries. Performing work on molding particularly complex products and structures. Supervision of work on cleaning, lubricating, assembling molds, installations and accepting them when ready. Laying into the mold (installation) of individual elements of the reinforcing frame with enlarged assembly and fixation in the design position. Installation of embedded parts and mounting loops. Installation of prestressed reinforcement into forms with electrothermal or mechanical (using jacks or tensioning stations) tension. Installation of liners and cores. Filling the form (installation) with concrete mixture. Compacting the concrete mixture. Grouting of exposed surfaces of molded products. Slinging of products with their delivery to the place of heat treatment. Unmolding of products with their transportation to a finishing post or to a stack. Control during the molding process the operation of all available machines and mechanisms (except for the volumetric molding machine).

Must know: design of serviced equipment and methods of regulating its operation; basic methods for quality control of gypsum dough and plasterboard sheets; rules for keeping entries in the journal; design and principle of operation of serviced machines and installations; methods and rules for laying and tensioning reinforcement; technical requirements for manufactured products; rules for reading drawings; requirements of technological maps for molding modes; techniques and methods for slinging and moving products.

Work examples

Molding:

1. Gable rafter beams, sub-rafter beams, crane beams.

2. Architectural concrete products.

3. Working chambers for sewer, drainage, rainwater, water and gas wells; telephone boxes and wells.

4. Two-branch crane columns.

5. Reinforced concrete rings for silos and elevators, volumetric elevator shafts, volumetric collector sections.

6. Flights of stairs with half landings.

7. External wall panels with natural stone cladding.

8. Span structures of bridges and overpasses.

9. Pressure pipes.

10. Rafter and truss trusses.

\Typical job description for manual molder, 3rd category

Job description Manual molder 3rd category

Job title: Manual molder 3rd class
Subdivision: _________________________

1. General Provisions:

Subordination:
• Manual molder of the 3rd category is directly subordinate...................
• Manual molder of the 3rd category follows the instructions................................................. ..........

(the instructions of these employees are followed only if they do not contradict the instructions of the immediate supervisor).

Substitution:

• Manual molder of the 3rd category replaces.................................................... .......................................
• Replaces a manual molder of the 3rd category.................................................... ....................................

Hiring and dismissal:
A manual molder is appointed to the position and dismissed by the head of the department in agreement with the head of the department.

Must know:

• composition and properties of molding sands and other materials used for the manufacture of molds
• dimensions of allowances for shrinkage and processing
• density of mold filling and their gas permeability, cross-sectional ratio, relative position and dimensions of the riser, feeder and slag trap
• sequence of manufacturing shell molds and cores
• requirements for ready-made forms
• device and method of using instrumentation and devices used, gating systems
• shell firing mode.

• Manual molding using models and templates, in flasks or in soil, of large simple castings, as well as medium-sized complex castings with shaped surfaces, with a large number of cores and detachable parts.
• Manual molding of shell halves and cores for large castings with complex configurations.
• Hot gluing of shell forms with pulverbakelite.
• Assembling shell molds with installation of complex rods.
• Making molds using complex templates and simple skeletal models.
• Manual molding according to models of ship fittings from carbon steels, tested under pressure up to 5 MPa (50 atm), from non-ferrous alloys, tested under pressure up to 3 MPa (30 atm).
• Assembling molds of medium complexity with installation of refrigerators and rods.
• Stuffing and compacting molds for complex and large custom castings, pinning, painting and fastening molds for complex castings in conjunction with a more highly qualified hand molder.
• Controlling lifting and transport equipment from the floor, slinging containers, tying loads for lifting and moving.

4. Rights

• A manual molder has the right to give instructions and tasks to subordinate employees on a range of issues included in his functional responsibilities.
• The manual molder has the right to control the implementation of production tasks and the timely execution of individual orders by employees subordinate to him.
• The hand molder has the right to request and receive the necessary materials and documents related to his activities and the activities of his subordinate employees.
• The manual molder has the right to interact with other services of the enterprise on production and other issues included in his functional responsibilities.
• The manual molder has the right to get acquainted with the draft decisions of the enterprise management concerning the activities of the Division.
• The manual molder has the right to submit proposals for the manager’s consideration to improve work related to the responsibilities provided for in this Job Description.
• The manual molder has the right to submit for consideration to the manager proposals on rewarding distinguished workers and imposing penalties on violators of production and labor discipline.
• The manual molder has the right to report to the manager about all identified violations and shortcomings in connection with the work performed.

• The hand molder is responsible for improper performance or failure to fulfill his job responsibilities provided for by this job description - within the limits specified labor legislation Russian Federation.
• The hand molder is responsible for violating the rules and regulations governing the business.
• When transferring to another job or being released from a position, the Manual Molder is responsible for the proper and timely delivery of work to the person taking up the current position, and in the absence of one, to the person replacing him or directly to his supervisor.
• The manual molder is responsible for offenses committed in the course of his activities - within the limits determined by the current administrative, criminal and civil legislation of the Russian Federation.
• The hand molder is responsible for causing material damage- within the limits determined by the current labor and civil legislation of the Russian Federation.
• The Hand Molder is responsible for complying with applicable instructions, orders and regulations regarding the maintenance of trade secrets and confidential information.
• The manual molder is responsible for compliance with internal regulations, safety and fire safety rules.

Head of structural

Job description for a molder of reinforced concrete products and structures

I. General provisions:

1. Moulder of reinforced concrete products and structures 3 r. appointed, moved and dismissed from his position by order of the head of the enterprise, upon the proposal of the head of the BSU.
2. Menstrual tariff rate The molder is set according to the staffing schedule.
3. Directly reports to the head of the BSU.

II. Tasks and Responsibilities molder of reinforced concrete products and structures 3 rubles:

1. Carrying out work on forming reinforced concrete products of simple and medium complexity.
2. Cleaning, lubricating and assembling molds.
3. Laying ready-made reinforcing mesh, frames and embedded parts into the mold and fixing them in the design position.
4. Installation of prestressed reinforcement with electrothermal tensioning method, liners and removable dividing panels into molds.
5. Filling the mold with concrete mixture, leveling and compacting using a vibrator.
6. Finishing the exposed surfaces of a molded product.
7. Slinging products and transporting them to heat treatment chambers.
8. Unmolding of the product with transportation to the finishing post or to the stack.
9. Checking the correct assembly, fastening of forms and the quality of the supplied mass.
10. Stripping products from molds or pallets.
11. Dismantling molds, placing products in a stack, on a roller conveyor or other transport equipment.
12. Sorting of defective products.

III. Employee Compliance Responsibilities

regulatory legal acts on labor protection:

1. Must take care of personal safety and health, as well as the safety and health of others while performing any work or while on the premises of the enterprise.
2. Know and comply with the requirements of regulatory legal acts on labor protection, rules for handling machines, mechanisms, equipment and other means of production, use collective and individual protective equipment.
3. Undergo preliminary and periodic medical examinations in accordance with the procedure established by law.

IV. Must know

Standards of linear dimensions;

Forming methods and techniques;

Design and principle of operation of the equipment used;

Methods and rules for laying and tensioning reinforcement;

Technical requirements for manufactured products;

Requirements of technological maps for molding modes;

Techniques and methods for slinging and moving products;

Rules for assembling and disassembling forms;

The order of filling forms;

Setting times for the mortar and methods for testing blocks and slabs for strength;

Device of forms;

Rules for stripping products and their installation;

Rules, procedure for cleaning and assembling forms;

Properties of lubricants;

Labor regulations of the enterprise;

Rules and regulations of labor protection, safety, industrial sanitation and fire safety.

V. Rights:

1. Request and receive the necessary materials and documents related to the issues of their activities.
2. Make proposals to senior management to improve the organization of their work.
3. Get acquainted with the draft decisions of the enterprise management concerning its activities.

VI. Responsibility:

The molder of reinforced concrete products and structures is personally responsible for:

1. Improper performance or failure to fulfill one's official duties as provided for in this instruction - within the limits determined by the current labor legislation of Ukraine.
2. For offenses committed in the course of carrying out its activities - within the limits determined by the current administrative, criminal and civil legislation
3. Giving false information about the status of the work being performed.
4. Violations of the requirements of laws and other legal acts on labor protection.

VII. Relationships:

All issues related to the organization of his work and the performance of his duties are coordinated directly with his supervisor.

VIII. Qualification requirements:

Must have a special education and a corresponding certificate of assignment of working qualifications as a molder of reinforced concrete products and structures.

Supervisor structural unit ________________ __ __________ G.

(signature, full name)

AGREED:

Legal Advisor ______________________________ __ __________

(signature, full name)

Labor safety engineer ______________________________ __ __________

(signature, full name)

I have read the instructions: _____________________________ __ __________

(signature, full name)

General provisions

requirements of technological maps for formation modes; techniques and methods of slinging and moving products.

* - For a molder of reinforced concrete products and structures of the 2nd category, a basic or incomplete basic general secondary education is required. Obtaining a profession directly in production. No work experience requirements.

For a molder of reinforced concrete products and structures of the 3rd category, you need complete or basic general secondary education. Vocational education without requirements for work experience or obtaining a profession directly in production, advanced training and work experience as a molder of reinforced concrete products and structures of the 2nd category for at least 1 year.

For a molder of reinforced concrete products and structures of the 4th category, complete or basic general secondary education. Vocational and technical education. Training. Work experience as a molder of reinforced concrete products and structures of the 3rd category for at least 1 year.

3.1 External documents:

3.2 Internal documents:

Charter of the enterprise, Orders and instructions of the director of the enterprise (head of department); Regulations on the production department, Job description for a molder of reinforced concrete products and structures, Internal labor regulations.

4.1. Performs work on the formation of particularly complex and critical products and structures.

4.2. Supervises the work of cleaning, lubricating and folding forms and installations and takes them to the extent of readiness.

4.3. Places individual elements of the reinforcement frame into the mold (installation) with increased folding and fixation in the design position.

4.4. Installs backfill parts and mounting loops.

4.5. Installs prestressed reinforcement at the mold with electrothermal or mechanical (using jacks or tensioning stations) tension.

4.6. Installs liners and core.

4.7. Fills forms (installations) with concrete mixture.

4.8. Compacts the concrete mixture.

4.9. Rubs open surfaces of molded products.

4.10. Slings products and presents them to the place of heat treatment.

4.11. Unpacks products and transports them to a processing post or to a stack.

4.12. During the formation process, he supervises the work of all available machines and mechanisms (except for the volumetric molding machine).

The molder of reinforced concrete products and structures has the right:

5.1. Familiarize yourself with the draft decisions of the enterprise management concerning its activities.

5.2. Submit proposals for improvement of work related to the responsibilities provided for in these instructions for consideration by management.

5.3. Within your competence, inform your immediate supervisor about all shortcomings identified in the course of your activities and make proposals for their elimination.

5.4. Request personally or on behalf of your immediate supervisor from heads of departments of the enterprise and specialists information and documents necessary to perform their job duties.

5.5. Require the management of the enterprise to provide assistance in the performance of their official duties and rights.

The molder of reinforced concrete products and structures is responsible for:

6.1. For improper performance or failure to fulfill one’s official duties as provided for in this job description - within the limits determined by the current labor legislation of Ukraine.

6.2. For offenses committed in the course of carrying out their activities - within the limits determined by the current administrative, criminal and civil legislation of Ukraine.

6.3. For causing material damage - within the limits determined by the current labor and civil legislation of Ukraine.

The work schedule of a molder of reinforced concrete products and structures is determined in accordance with the Internal Labor Regulations established at the enterprise.

The terms of remuneration for the molder of reinforced concrete products and structures are determined in accordance with the Regulations on remuneration of personnel.

9 Final provisions

This Job Description is drawn up in two copies, one of which is kept by the Company, the other by the employee.

Tasks, Responsibilities, Rights and Responsibilities can be clarified in accordance with changes in the Structure, Tasks and Functions of the structural unit and workplace.

Changes and additions to this Job Description are made by order of the General Director of the enterprise.